Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile ChaityendraLevel-12 Asked: January 17, 2021In: Steel Design What is slenderness ratio in steel structure?
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: January 12, 2021In: Steel Design The maximum permissible stress for power driven field rivet in bearing on rivet is? Poll Results 0%A- 100 N/mm2 0%B- 250 N/mm2 50%C- 270 N/mm2 ( 2 voters ) 50%D- 300N/mm2 ( 2 voters ) Based On 4 Votes Participate in Poll, Choose Your Answer. A- 100 N/mm2 B- 250 N/mm2 C- 270 N/mm2 D- 300N/mm2
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: January 11, 2021In: Steel Design In a grillage footing the maximum shear force occurs at? Poll Results 0%A- Edge of grillage beam 0%B- Centre of base plate 0%C- Center of grillage beam 100%D- None of these ( 1 voter ) Based On 1 Vote Participate in Poll, Choose Your Answer. A- Edge of grillage beam B- Centre of base plate C- Center of grillage beam D- None of these
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: January 10, 2021In: Steel Design The spacing between adjacent bents in a roof truss is called? Poll Results 0%A- Purlins 100%B- Bay ( 1 voter ) 0%C- Knee 0%D- Braces Based On 1 Vote Participate in Poll, Choose Your Answer. A- Purlins B- Bay C- Knee D- Braces
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: January 10, 2021In: Steel Design The member of roof truss which supports the purlins is called as? Poll Results 0%A- Sag rod 0%B- Main strut 100%C- Pricipal rafter ( 1 voter ) 0%D- Principal tie Based On 1 Vote Participate in Poll, Choose Your Answer. A- Sag rod B- Main strut C- Pricipal rafter D- Principal tie
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: January 10, 2021In: Steel Design Normally, the angle of roof truss with asbestos sheets should not be less than? Poll Results 0%A- Less than 26° 100%B- Less than 30° ( 2 voters ) 0%C- Less than 40° 0%D- None of the above Based On 2 Votes Participate in Poll, Choose Your Answer. A- Less than 26° B- Less than 30° C- Less than 40° D- None of the above
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: January 10, 2021In: Steel Design The economic spacing of a roof truss depends upon the? Poll Results 66.67%A- Cost of purlins and cost of roof coverings ( 2 voters ) 0%B- Cost of roof covering and dead loads 33.33%C- Dead loads and live loads ( 1 voter ) 0%D- Live loads and cost of purlins Based On 3 Votes Participate in Poll, Choose Your Answer. A- Cost of purlins and cost of roof coverings B- Cost of roof covering and dead loads C- Dead loads and live loads D- Live loads and cost of purlins
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: December 21, 2020In: Steel Design Which one of the following is the mode of failure in a fillet weld material? Poll Results 0%A- Tension 100%B- Shear ( 1 voter ) 0%C- Bearing 0%D- Crushing Based On 1 Vote Participate in Poll, Choose Your Answer. A- Tension B- Shear C- Bearing D- Crushing
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: September 11, 2020In: Steel Design The maximum diameter of a bar used in a ribbed slab is? Poll Results 0%A- 12 mm 0%B- 6 mm 0%C- 20 mm 100%D- 22 mm ( 1 voter ) Based On 1 Vote Participate in Poll, Choose Your Answer. A- 12 mm B- 6 mm C- 20 mm D- 22 mm
Chaityendra 350 Questions 257 Answers 234 Best Answers 787 Points View Profile Poll ChaityendraLevel-12 Asked: September 11, 2020In: Steel Design A circular slab subjected to external loading deflects to form? Poll Results 0%A- Semi hemisphere 0%B- Ellipsoid 100%C- Paraboloid ( 3 voters ) 0%D- None of these Based On 3 Votes Participate in Poll, Choose Your Answer. A- Semi hemisphere B- Ellipsoid C- Paraboloid D- None of these
